On This Page
This set of Production Engineering Multiple Choice Questions & Answers (MCQs) focuses on Production Engineering Set 25
Q1 | Which one of the following methods be used for turning internal tapers only?
- Taper attachment
- Reamer
- Form tool
- Compound rest
- Tailstock offset
Q2 | Folding process of edges of the sheet metal is termed as
- Bending
- Seaming
- Hemming
- Parting off
Q3 | In which operation on a work piece on lathe the spindle speed with be least?
- Plain turning
- Thread cutting
- Taper turning
- Finishing
- Parting off
Q4 | Specific temperature for the international Prototype metre is
- Atmospheric
- Melting point of ice
- 0?F
- 0?K
- 0?C
Q5 | The speed of grinding wheel is limited by
- type of bond
- grinding operation
- rigidity of grinding machine
- All of the above
- Parting off
Q6 | Which of the following is not a shearing process?
- Notching
- Perforating
- Lancing
- Blanking
- Embossing
Q7 | For which of the following material TIG welding is preferred?
- Gold
- Stainless steel
- Mild steel
- Silver
- Aluminium
Q8 | Taper gererally used in lathes now-a-days is
- Jarno
- Morse
- Brown and sharpe
- None of above
- Parkinson
Q9 | Point angle of 90? is used on drills for drilling on
- Parting off
- brass
- bakelite
- very hard materials
- aluminium
Q10 | In which of the following process hydraulic fluid acts as transfer media?
- Ultrasonic machining
- Electron beam machining
- Water jet machining
- Iron beam machining
- Electro discharge machining
Q11 | The pouring temperature for grey cast iron is
- 2350?C
- 1655?C
- 1850?C
- 1400?C
- 1000?C
Q12 | The surface accuracy of slip gauges is of the order of
- 0.02
- 0.0002
- 0.002
- 0.2
- 0.00002
Q13 | Inside and outside diameters of a thin tube are to be measured. Only one of the following tools is to be selected. Which one would you choose?
- Outside caliper
- Odd-leg caliper
- Inside caliper
- Trammel
- Vernier caliper
Q14 | The process for producing smooth surfaces by plastically moving away the raised micro-irregularities on the surface and passing it into the microcavities is known as
- Buffing
- Super finishing
- Burnishing
- Tumbling
- Polishing
Q15 | In machine tools normally spindle speeds vary in
- Arithmetical progression
- Geometrical progression
- Exponential progression
- Logarithmic progression
- None of the above
Q16 | The length of a hacksaw blade is measured from
- Centre of hole at one end to the centre of hole at the other end
- None of these
- The formula L = 16 x width
- Extreme one to-extreme end
- 1830 rpm
Q17 | The usual ratio of forward and return stroke in shaper is
- 2 ; 3
- 3 ; 2
- 4 ; 3
- 1 ; 2
- 3 ; 4
Q18 | The machining allowance provided on pattern depends on
- The casting orientation
- Size and shape of casting
- Degree of accuracy required
- All of the above
- None of above
Q19 | Cutting speed in turning operations is maximum in case of
- Cast iron
- Mild steel
- Aluminium
- Bronze
- Brass
Q20 | Which of the following is dead soft steel?
- Parting off
- C 45
- 11 Mn 2
- C 04
- 33 Mo 55.
Q21 | As per ISS a steel specified as T 75 W 18 Co 10 Cr 4V2 will not have (as constituent)
- Cobalt
- Chromium
- Vanadium
- Electrical stampings
- Copper
Q22 | The limitation of electronically operated automatic control system is
- Considerable time lag
- Poor accuracy
- Complicated control response
- It requires eloborate protection in hazardous locations
- Serious effect of ambient conduction
Q23 | The equal percentage characteristic of a valve is
- Uniform flow rate
- Flow rate proportional to valve lift
- Each increment of plug movement produces a change in flow which is proportional to the amount flowing before the change occurred
- Percentage increase in flow is equal to the percentage increase in lift
- The flow rate before the plug movement is equal to the flow rate after the movement
Q24 | Mould washes are used to produce
- castings with different hardnesses at different locations
- smooth surface on castings
- castings with symmetrical sections
- None of the above
- Parting off
Q25 | Two 20 mm thick plates are to be gas welded. What size of welding rod should be selected out of the following rods available?
- 6 mm
- 4.5 mm
- 1.5 mm
- 8 mm
- 3 mm