On This Page
This set of Production Engineering Multiple Choice Questions & Answers (MCQs) focuses on Production Engineering Set 20
Q1 | Photoelectric transducers are used for the measurement of any phenomenon which can be used to produce
- Variation in current
- Variation in voltage
- Variation in light intensity
- Variation in flux density
- Any of the above
Q2 | Chisels for metal cutting are
- Hardened in the middle
- Hardened at cutting edge
- Hardened all over
- Hardened at random
- Never hardened
Q3 | Kind of tools used to undercut corners on a job that is to be hardened and ground is
- Vee shaped tool
- Form tool
- Knurling tool
- Roundnose tool
- Parting tool
Q4 | If a drill has different lengths of cutting edges
- Cutting edge will be over size
- The drilled hole will be rough
- The drilled hole will not be circular
- The drilled hole will be smooth
- Cutting edge will become blunt rapidly
Q5 | Plastic gears are used in
- Toys
- Instruments
- Low load applications
- Low noise applications
- Any of the above
Q6 | Fine sand is used for preparing the moulds for
- Symmetrical castings
- Large castings
- Small castings
- Non-ferrous castings
- Centrifugal castings
Q7 | Which one of the following measuring instruments is supposed to be most accurate?
- Micrometer
- Vernier dial gauge
- Optical projector
- Steel scale
- Vernier caliper
Q8 | A diamond point chisel is used for
- V-shaped grooves
- Spherical surfaces
- Flat surfaces
- Convex surfaces
- Round surfaces
Q9 | Which of the following is a chipless machining process?
- Metal spinning
- Knurling
- Hobbing
- Lapping
- None of the above
Q10 | With HSS tools the maximum safe operating temperature is of the order of
- 200?C
- 440?C
- 640?C
- 540?C
- 340?C
Q11 | Relief angle on HSS tools usually vary from
- 11 to 15?
- 22 to 27?
- 16 to 150?
- 28 to 30?
- 3 to 10?
Q12 | Spiral flutes are provided on drill bits to
- Help from the cutting edge of the drill point
- Curl the chip tightly for easier removal
- Provide passage for coolant supply
- All of the above
- None of the above
Q13 | Which one of the following is supposed to be least accurate?
- Surface plate
- Air gauge
- Optical projector
- Vernier micrometer
- Steel scale
Q14 | Automobile gears are generally made of
- Alloy steel
- Cast iron
- Nitrided steel
- Cast steel
- Non-ferrous materials
Q15 | Marform is
- Is a foming process on lathe in which movement of tool is neither governed by cross slide nor by compound slide
- A work holding device in which plane of rotation can be changed while working
- A darwing process that forms metal sheet by using a movable steel punch and a rubber headed ram
- Is a forming tool and on lathe machine to generate spherical surfaces
- Is a gauge used to check regular surfaces
Q16 | For aluminium, the cutting speed on lathe is around
- 150 m/min
- 300 m/min
- 100 m/min
- 1000 m/min
- 30 m/min
Q17 | Which of the following defect results due to mixing of two streams of molten metal that are too cold to fuse properly?
- Cold shut
- Swell
- Honey coming
- Scab
- Shrinkage
Q18 | The range of voltage (open circuit) in are welding is generally
- 20 - 40 V
- 100 - 150 V
- 40 - 90 V
- 150 - 230 V
- 400 - 440 V
Q19 | A Bourdon tube is generally made of
- Monel metal
- Beryllium copper alloy
- Phosphor bronze
- Stainless steel
- Any of the above
Q20 | The chemical used in generating acetylene is
- Charcoal
- Calcium carbonate
- Calcium carbide
- Carbon
- Crushed bone
Q21 | Which one of the following is not a part of micrometer
- Sleeve
- Spindle
- Thimble
- Anvil
- Beam
Q22 | Plug rolling is used to
- Reduce the wall thickness and increase the diameter of tubes already made
- Remove out of roundness of pipes
- Increase the wall thickness of pipes at ends
- Reduce the diameter of pipe
- Cut threads at the ends of pipes
Q23 | Burr is
- Boundary between finished and unifinished portion on a work piece
- Sharp edge remaining on the metal after curring, stamping or machining
- A marking or work piece to identify for correct position on a work piece
- Burnt surface of a casting
- Unmachined portion of work piece
Q24 | Which process is used for manufacturing the body of a carburettor?
- Die casting
- Fine sand casting
- Electro forming
- Sintering
- Metal spraying
Q25 | The silver point temperature is
- 760?C
- 1500.5?C
- 500?C
- 960.5?C
- 1100.5?C