On This Page
This set of Production Engineering Multiple Choice Questions & Answers (MCQs) focuses on Production Engineering Set 6
Q1 | Loam moulds are
- Used for symmetrical castings
- Used in centrifugal castings
- Used for very small articles
- Made out of wet sand and then skin dried
- Used for large castings
Q2 | A thin tube is to be cut by hacksawing. Blades with following TPI are available which blade will be appropriate for the job
- 14 TPI
- 4- TPI
- 18 TPI
- 32 TPI
- 20 TPI
Q3 | The function of a transducer is
- To decodify the input signal
- To convert the primary signal into a more useful quantity usually an electrical impulse
- To amplify the input signal
- To codify the input signal
- To modify the input signal
Q4 | Flange wrinkling is a defect associated with
- Cold heating
- Cold rolling
- Deep drawing
- Die casting
- None of the above
Q5 | Low helix drills are used for machining
- Brass
- bronze
- bakelite
- Any of the above
- Parting off
Q6 | During continuous chip formation the maximum heat is taken away by
- Depends on velocity of cutting
- Chip
- Tool
- Work piece
- Coolant
Q7 | Folding of edges of the sheet metal is done to
- Parting off
- To make the product stronger
- To make the product attractive
- Strengthen the edges and eliminate the sharp edges
Q8 | Poor surface finish and fast wear of tool are the characteristics of
- Continuous chips with built up edges
- Discontinuous chips
- Inhomogencous chips
- Low power consumption
- Continuous chips
Q9 | In a Brinell hardness test the hardness number is determined by the measurement of
- Width of depression
- Depth of depression
- Diameter of depression
- Surface area of depression
- None of the above
Q10 | Post cleaning is done in case of brazed joints to
- Prevent corrosion
- Remove scale
- Strengthen the joint
- Increase the strength of the joint
- All of the above
Q11 | For cutting sheet metal the chisel cutting edge is bevelled to an angle of
- 90?
- 40? - 45?
- 30? - 60?
- Parting off
Q12 | Core prints are
- Impressions left on cores during core making
- Hard surfaces on cores mainly meant for resisting deformation
- Blue prints for core manufacturing
- Holes or recesses in core meant for locating cores in position
- None of the above
Q13 | The most commonly used instrument for the measurement of mass or volume of flowing fluids in industrial plants are
- Impeller type
- Propeller type
- Turbine type
- Weight belt type
- Any of the above
Q14 | During arc welding if the current is too low, it is likely to result in
- Poor penetration
- Excess piling up of weld metal
- Excessive electrode consumption
- All of the above
- None
Q15 | The disadvantage of die casting process is
- Cost is less
- Surface finish is poor
- Heavy section can be easily cast
- High production rates are not possible
- Only certain non-ferrous alloys can be cast economically
Q16 | Which of the following provides an additional projection on a pattern and also forms a seat to support and locate the core in the mould?
- Head
- Mould print
- Check
- Core print
Q17 | Aluminium gears are generally used in
- Compressors
- Speed reducers
- Instruments
- Worm wheels
- None of the above
Q18 | While machining copper alloys by electro chemical machining the electrolyte used is
- Sodium chlorate
- Sodium hydroxide
- Sodium sulphate
- Common salt
- Sodium nitrate
Q19 | Which of the following is relatively a low temperature brazing process?
- Brass brazing
- Silver manganese brazing
- Copper brazing
- Nickel chrome brazing
- Silver brazing
Q20 | In electrical resistance welding when the current passes through the metal, the greatest resistance is
- At the surface
- Through the metals to be welded
- At the point of contact of the metal to be welded
- At the point where electrode contacts the metal
- None of the above
Q21 | The material for worm wheels is usually
- Bronze
- Cast iron
- Copper
- Aluminium
- Cast steel
Q22 | In die casting process
- The cost of dies is generally insignificant
- Very high production rates are possible
- Any size of casting can be prepared
- Any metal can be cast
- Dimensional accuracy is immaterial
Q23 | For resistance welding
- Voltage is low and current is high
- Voltage is high and current is low
- Both voltage and current are high
- Both voltage and current are low
- None of the above
Q24 | Teeth of a hacksaw are
- In a single plane
- Parting off
- Bent in one direction only
- Bent alternately in opposite directions
Q25 | Die casted gears are generally used in
- Counters
- Toys
- Cameras
- Any of the above
- None of the above