On This Page
This set of Production Engineering Multiple Choice Questions & Answers (MCQs) focuses on Production Engineering Set 8
Q1 | The minimum section thickness for cast iron castings is
- 10 mm
- Parting off
- 3 mm
- 1 mm
- 6 mm
Q2 | When large number of components are turned and parted off from a bar, the chuck used is
- Magnetic chuck
- Four jaw chuck
- Collet chuck
- Face place
- Three jaw chuck
Q3 | Which of the following plate can be used for milling the sides of a hexagon nut?
- Parting off
- 3 hole circle plate
- 45 hole circle plate
- 55 hole circle plate
- 24 hole circle plate
Q4 | Stub tooth are cut on gears
- To improve transmission efficiency
- To reduce centre distance between shafts
- None of above
- To reduce frictional torque
- Subjected to shock and vibration
Q5 | Porosity of a welded joint may be caused by
- Poor base metal
- Low welding current
- High welding current
- Wrong size of electrode
- None of the above
Q6 | Ionised material acts as transfer media in case of
- Ion beam machining
- Plasma arc machining
- Electro discharge machining
- All of the above
- None of the above
Q7 | Scale sensitivity is defined as
- Ratio of a change in scale reading to the corresponding change in pointer deflection
- Least reading of scale/range of scale
- Least reading of scale/unit measurable quantity
- Least count of scale/range of scale
- None of the above
Q8 | Which one does not fit with the rest in the following
- Hammer
- Flatter
- Hot chiesel
- Reamer
- Hot punch
Q9 | Kerosene is used as a cutting fluid while machining
- Magnesium
- Low carbon steel
- Copper
- Brass
- Aluminium
Q10 | Out of the following tools which one is expected to have highest carbon percentage
- Crowbar
- Ordinary file
- Circular saw
- Pliers
- Wrenches
Q11 | For welding of non-ferrous materials which of the following is preferred?
- Microwave frequency voltage
- Low frequency ac
- High frequency ac
- Direct current
- Induction heating
Q12 | As far as machinability is concerned, which of the following will be considered to be most inferior alloy?
- Malleable cast iron
- Parting off
- Monel metal
- Gun metal
- Bearing bronze
Q13 | Precision is
- The ability of a measuring device to detect small differences in a quantity being measured
- Agreement of the result of a measurement with the true value of the measured quantity
- The ability of an instrument to reproduce same reading under identical conditions
- The repeatability of a measurement process
- Error of judgment in reading on observation
Q14 | In centrifugal castings, the cores are generally made of
- Green sand and molasses
- Plastic
- Wax
- Cores are not used
- Plaster of paris
Q15 | In orthogoual cutting of metals the cutting edge is
- Perpendicular to the direction of tool travel
- Perpendicular to the work piece
- Perpendicular to the shear plane
- Perpendicular to the axis of cutting tool
- None of the above
Q16 | Hardest abrasive is
- Aluminium oxide
- Silicon carbide
- Boron carbide
- Diamond
- Tungsten oxide
Q17 | Riser is generally located
- near the parting line
- on the upper most section of the casting
- Parting off
- opposite to the pouring end
- near the deepest section of the mould
Q18 | Which of the following test can be used to detect surface cracks in the welding of non-magnetic alloys?
- Fluorescent test
- Gamma ray test
- X-ray test
- Magnaflux test
- Any of the above
Q19 | Which of the following process has the lowest rate of metal removal?
- Electron beam machining
- Electro discharge machining
- Abrasive jet machining
- Electro chemical machining
- Chemical machining
Q20 | Which of the following machine is likely to be extensively used in a workshop manufacturing wire nails?
- Lathe
- Broaching machine
- Drilling machine
- Power press
- Cold heading machine
Q21 | Shearing strain in the chip at shear plane is
- tan (? + ?) + cot ?
- tan (? - ?) - tan ?
- Infinite clearance
- tan (? - ?) + cot ?
- tan (? - ?) + tan ?
Q22 | Which of the following is the most common bond used in grinding wheels?
- Shellac bond
- Pakelite bond
- Parting off
- Rubber bond
- Vitrified bond
Q23 | The grain size of moulding sand is expressed in terms of
- Mean grain diameter
- Seive number
- Grain diameter
- Grain density
- Grain fitness number
Q24 | Refractory metals are
- Those which can be cast in the form of bricks
- Those which reflect heat
- Those which have melting point above 1950?C
- Those which absorb heat
- Those do not malt in a normal furnace
Q25 | Press die life is gauged by
- loss in weight
- amount of burr produced
- change of colour
- Any of the above
- Parting off