On This Page
This set of Production Engineering Multiple Choice Questions & Answers (MCQs) focuses on Production Engineering Set 16
Q1 | Hardness tester used for determining the hardness of a core is bearly identical to which of the following?
- Vickers hardness tester
- Rockwell hardness tester
- Brinell hardness tester
- Shore's scleroscope
- Parting off
Q2 | In gang milling
- Work is fed into the rotation of cutter
- A cutter generates two or more plain surface simultaneously
- Work moves in the opposite direction as the rotating of the cutter
- Work moves in the same direction as the rotation of the cutter
- More than one cutter is simultaneously used
Q3 | A gagger is
- A tool used in clearing material before welding
- A, L shaped metal accessory used in floor moulds to support hanging bodies of sand in cope
- A device for removing foreign particles from sand
- A tool used in clearing welds
- A tool used in foundry for cleaning of castings
Q4 | Which of the following is gear finishing process?
- Gear lapping
- Gear shaving
- Gear grinding
- All of the above
- None of the above
Q5 | Abrasive GC indicates
- White Al2O3
- Parting off
- Al2O3
- Green grit SiC
- SiC
Q6 | The primary detector in a pressure gauge is usually
- Bellows
- Diaphragm
- Spring
- Bourdon tube
- Coil spring
Q7 | Which type of gears can be manufactured by extrusion process?
- Spur gears
- Bevel gears
- Helical gears
- Worm gears
- Herringbone gears
Q8 | Chip breaker is
- an obstruction attached to face of the tool
- a hammer used to break the chips
- a coolant forced under pressure on the chip
- None of the above
- Parting off
Q9 | Point angle of 135 to 150? is used on drills while drilling
- hard steels
- nickel alloys
- thin sheet metals
- Any of the above
- Parting off
Q10 | Back rake angle while turning brass is
- 5?
- 10?
- Parting off
- 22?
- 0?
Q11 | The cutting tool is
- Goose neck tool
- Parting tool
- Threading tool
- Boring tool
- Drilling tool
Q12 | The standard taper provided on the tapered shank of drills is known as
- Chapman taper
- Morse taper
- Jarno taper
- Taper No. 1
- None of the above
Q13 | A gear has a pitch diameter of 5.732 inches and circular pitch
- 5
- 9
- 7
- 3
- 1
Q14 | Which of the following material is difficult to be spot welded?
- Cold rolled mild steel sheet
- Hot rolled mild steel sheet
- Stainless steel
- Copper
- None of the above
Q15 | Hardness of diamond can be determined by
- Brinell hardness tester
- Rockwell hardness tester
- Vickers hardness tester
- None of the above
- Parting off
Q16 | In case of turning or milling, the surface roughness is expected to be in the range (
- 20 to 50
- 5 to 15
- 50 to 100
- 100 to 250
- 250 to 500
Q17 | True centrifugal casting is used to
- Get accurate castings
- Get chilled castings
- Get dynamically balanced castings
- Get statistically balanced castings
- Cast objects symmetrical about an axis
Q18 | While using high speed steel tools, the cutting speed will be highest for which of the following steel?
- Alloy
- Stainless steel
- Parting off
- Medium carbon steel
- Mild steel
Q19 | If a piece of steel is reheated to a temperature of 200?C to 250?C immediately after quenching, the process is known as
- Hardening
- Cyniding
- Normalizing
- Tempering
- Annealing
Q20 | Spot facing is
- Localised machining of a component
- None of above
- A spot prepared on shaper or milling machine
- Machining of a spot to fit other parts
- Mahining of spol on the surface of a part to furnish a flat bearing or the head of a holt or nut
Q21 | Hollow punches are used for making holes upto
- 10 mm and above
- Parting off
- (5 - 8) mm
- (6 - 9) mm
Q22 | A plug gauge is used for measuring
- Spherical holes
- None of above
- Screw threads
- Cylindrical bores
- Taper bores
Q23 | Angle plate is
- Used for measurement of angles
- Used for cutting angles on jobs on shaper
- Used for holding angular jobs in milling machine.
- Cast iron jig used to hold work in a vertical position of layout or machining
- None of above
Q24 | Ablation mechanism is used in which of the following machining process?
- Water jet machining
- Chemical machining
- Laser beam machining
- Ultrasonic machining
- Electron beam machining
Q25 | A photo-electric device in which the resistance of the metal changes directly proportional to the ligh striking on it is known as
- Photo-cell
- Photo-emission
- Photo-voltaic cell
- Photo-conductive cell
- None of the above