On This Page
This set of Machine Design Multiple Choice Questions & Answers (MCQs) focuses on Machine Design Set 16
Q1 | Forced vibrations
- Are preceded by free vibrations
- Are followed by free vibrations
- Have a frequency more than the natural frequency
- Are independent of natural frequency
- None of the above
Q2 | Bearings provided on passenger coaches in railway are
- Bush bearings
- Cast iron bearings
- Ball bearings
- Roller bearings
- Any of the above
Q3 | A coarse scres of major diameter 6 mm is designated as
- 6 M x 6 x 1
- M 6
- 6 M x 1
- 1 x 6 M
- Coarse M 6
Q4 | A reinforced concrete beam is considered as made of
- Homogeneous material
- Composite material
- Clad material
- Isotropic material
- Heterogeneous material
Q5 | In concrete mixer, the bevel gears for rotating the drum are generally
- Shaped
- Forged
- Hobbed
- Precisely machined
- Casted
Q6 | By using large thread angles in lifting machine
- The load will be sustained in absence of the other
- The load will be easily lifted
- The mechanical advantage will be high
- The mechanical advantage will be low
- While unloading, little effort will be required
Q7 | The holding power of sunk key is due to resistance which it offers in
- Shear
- Crushing
- Shear and crushing
- Tension
- (C) and (D) above
Q8 | Transverse fillet welded joints are designed for
- shear, tensile
- tensile, compressive
- tensile, shear
- compressive, shear
- Increasing the diameter of threaded portion
Q9 | The crest diameter of a screw thread is same as
- Pitch diameter
- Major diameter
- Pitch diameter
- Core diameter
- Minor diameter
Q10 | All the dimensions for a standard system of interchangeable gears can be defined in terms of
- Module
- Diametral pitch and circular pitch
- Pressure angle and pitch
- No of teeth and pitch circular diameter
- Addendum and dedendum
Q11 | Which of the following theory is also known as maximum shear stress theory of the failure of a material at the elastic limit
- Von Mises theory
- Guests Tresca theory
- Rankines theory
- Increasing the diameter of threaded portion
- Haig's theory
Q12 | A fillet weld having axis parallel to the direction of the applied load is known as
- side fillet weld
- end fillet weld
- diagonal fillet weld
- flat fillet weld
- Increasing the diameter of threaded portion
Q13 | As per Indian Boilers regulations the type of joint preferred for longitudinal joint is
- Reveted butt joint
- Any of above
- Riveted lap joint
- Welded joint
- Welded joint with cover plate
Q14 | In case of ball bearing
- Inner race should harder than outer race
- Outer race should be harder than balls
- Only cage should be hardened
- Inner race should be harder than balls
- Inner race, outer race and balls should be equally hardened
Q15 | The minimum thickness of steel members exposed to weather and accessible for painting is
- Increasing the diameter of threaded portion
- 6 mm
- 12 mm
- 8 mm
- 10 mm
Q16 | In case of brittle material the theory of elastic failure generally applied is
- Maximum total strain energy theory
- Maximum principal stress theory
- Distortion energy theory
- Maximum shear stress theory
- Maximum strain theory
Q17 | Stone erusher rolls are generally made
- Cast iron
- High carbon steel
- Mild steel
- Cast steel
- Grey iron
Q18 | The natural frequency of a shaft in bending is
- Nearly the same as the critical speed
- Nearly half the critical speed
- Exactly the same at which it is running
- Nearly double of the critical speed
- Depends on load and other factors
Q19 | Which of the following key transmits power through frictional resistance only
- Tangent key
- Saddle key
- Woodruff key
- Kennedy key
- Sunk key
Q20 | In the case of a cantilever, irrespective of the type, loading of the maximum bending moment and maximum shear force occur at
- Free end
- ?rd of length from fixed end
- Centre
- Increasing the diameter of threaded portion
- Fixed end
Q21 | Manganese in steel increases its
- Hardness
- Ductility and Malleability
- Tensile strength
- Brittleness
- Increasing the diameter of threaded portion
Q22 | The diameter of a washer is generally
- Equal to the diameter of bolt
- Slightly less than the diameter of the bolt
- Slight more than the diameter of the bolt
- Of any size that suits the application
- None of the above
Q23 | If a square key and the shaft are to be of the same material and of equal strength, the length of key would be (d = dia. Of shaft)
- 1.23 d
- 1.50 d
- 2 d
- d
- 0.75 d
Q24 | The segmental bottom of a circular tank is subjected to
- hoop tension
- hoop compression
- bending moment
- none of the above
- Increasing the diameter of threaded portion
Q25 | The pitch of 24 mm diameter metric threads would be
- 6 mm
- 1 mm
- 2 mm
- 5 mm
- 3 mm