On This Page
This set of Machine Design Multiple Choice Questions & Answers (MCQs) focuses on Machine Design Set 10
Q1 | The period during which a cam follower does not move is known as
- Free period
- Swell period
- Constant period
- Stationary period
- Fixed period
Q2 | A 3 mm diameter rivet must be squeezed to form a head. When yield stress in tension for this alloy is 125 Kpa, the minimum value of initiating force must be not less than
- 500 N
- 5000 N
- 1000 N
- Increasing the diameter of threaded portion
- 100 N
Q3 | Rankine formula is valid upto slenderness ratio of
- 100
- 150
- 60
- 120
- 80
Q4 | Tack welding
- Is a process of TIG welding
- Is a type of weld
- Is used for non-ferrous materials
- Is a preparation for welding
- None of the above
Q5 | Which is the lightest?
- 10 Quintals
- 1 British ton
- 1 U.S. long ton
- 1 metric ton
- 1 U.S. short ton
Q6 | M 10 secrews have a pitch of
- 0.5 mm
- 1.25 mm
- 5.00 mm
- 10 mm
- 2.50 mm
Q7 | Springs are used
- To store energy
- To reduce the magnitude of the transmitted force due to impact orshock
- To alter vibratory characteristics of a member
- To apply force or control motion
- Any of the above
Q8 | Which of the following is not a symmetrical section
- Circular
- 1 beam with equal flanges
- Equal angle iron
- All of the above
- 10 kg
Q9 | The cross-section of a standard fillet weld is a triangle with base angles of
- 45? and 45?
- Increasing the diameter of threaded portion
- 35? and 55?
- 60? and 30?
- 50? and 40?
Q10 | A key that transmits power through frictional resistance only is
- Saddle key
- Wood ruff key
- Square key
- All of the above
- None of the above
Q11 | The column which has the highest equivalent length has
- Both ends fixed
- One end fixed and other end free
- Both ends hinged and pin joined
- One end fixed and other end hinged
- None of the above
Q12 | Where a spring with a spring rate that increases with load is desired
- Soft springs are used
- Non-ferrous springs are used
- Elliptical section is preferred
- Conical spring are used
- None of the above
Q13 | Lowest value of joint efficiency is assumed in case of
- Single riveted butt joints
- Double riveted butt joints
- Single riveted lap joints
- Double riveted lap joints
- None of the above
Q14 | The rated life of a ball bearing vaires
- Inversely as cube of load
- Directly as load
- Directly as square of load
- Directly as cube of load
- Inversely as square of load
Q15 | IC engine cylinders are lubricated by
- thin film lubricated
- thick film lubrication
- either of (A) and (B) above
- none of the above
- Increasing the diameter of threaded portion
Q16 | Hydraulic testing of boilers is done at pressures
- Slightly above atmospheric pressure
- Below and above atmosphere
- At half the working pressure of boiler
- At 1
- At working pressure of boiler
Q17 | In case of pressure vessels having open ends the fluid pressure induces
- shear stress
- Increasing the diameter of threaded portion
- circumferential stress
- longitudinal compressive stress
- longitudinal tensile stress
Q18 | Size of rivet is specified by
- Weight
- Shape
- Volume
- Shank diameter
- Diameter of head
Q19 | For very heavy loads which of the following gear tooth profile will be preferred?
- 20? stub involute profile
- 14
- 14
- 14
- 20? full depth involute profile
Q20 | How many revolutions per minute one radian per second is equal to
- 3.6
- 5.949
- 9.549
- 1/3.6
- 1
Q21 | Gantry girders are invariably designed to resist
- transverse and lateral loads
- Increasing the diameter of threaded portion
- transverse, lateral and axial load
- lateral loads only
- transverse loads only
Q22 | The size of the fillet weld is given by
- throat of the fillet
- Increasing the diameter of threaded portion
- smaller size of the plate welded
- smaller side of the triangle
- hypotenuse of the triangle
Q23 | Cast iron bearings are used
- for reciprocating and oscillating motions only
- Increasing the diameter of threaded portion
- when space is the major consideration
- when cost is the major consideration
- for under water applications
Q24 | Splined shafts are most commonly used in
- aircrafts
- machine tools
- automobiles
- none of the above
- Cast steel
Q25 | The deflection of a helical spring is
- Directly proportional to d3
- Directly proportional to d3/2
- Directly proportional to d
- Directly proportional to d4
- Directly proportional to d2