On This Page
This set of Design of Machine Elements Multiple Choice Questions & Answers (MCQs) focuses on Design Of Machine Elements Set 3
Q1 | A knuckle joint is unsuitable for two rotating shafts, which transmit torque
- true
- false
Q2 | A maximum of how many roads may be connected using a knuckle joint?
- 2
- 3
- 4
- 5
Q3 | Which of the following are important parts of knuckle joint?
- eye
- pin
- fork
- each of the mentioned
Q4 | Calculate the diameter of pin from shear consideration with maximum shear stress allowed is 40NN/mm² and an axial tensile force of 50kN is acting on the rod.
- 39mm
- 44mm
- 49mm
- 52mm
Q5 | If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.
- 40mm
- 50mm
- 60mm
- 70mm
Q6 | A knuckle joint can be used in valve mechanism of a reciprocating engine.
- yes
- no
- yes but there are stress probles
- no as it is very dangerous to use
Q7 | Cotter joint is used when the members are subjected to which type of stresses?
- axial tensile
- axial compressive
- axial tensile or compressive
- none of the mentioned
Q8 | The principle of wedge action is used in cotter joint.
- true
- false
Q9 | Which of the following is not a part of cotter joint?
- socket
- spigot
- cotter
- collar
Q10 | Cold riveting holds the connected parts better than hot riveting.
- true
- false
Q11 | 67 N/mm².; Spigot dia=65mm; thickness 0f collar=15mm
- 131mm
- 139mm
- 141mm
- 149mm
Q12 | Cotter joint can be used to connect two rods for torque transmission purpose.
- true
- false
Q13 | Thickness of plate is required more in welding than in riveting.
- true
- false
Q14 | The capacity of welded structures to damp vibrations is quite good.
- true
- false
Q15 | Themit consists of a finely divided mixture of iron oxide and copper.
- true
- false
Q16 | Rails in the field are generally welded by using
- thermit welding
- gas welding
- electric arc welding
- forge welding
Q17 | In gas welding which of the following is generally used?
- oxygen-hydrogen
- oxygen-acetylene
- oxygen-hydrogen or oxygen-acetylene
- none of the mentioned
Q18 | Filler material is used in electric resistance welding.
- yes
- no filler material used
- depends on the type of welding
- none of the listed
Q19 | Which type of welding is generally used in automobile sector?
- electric arc welding
- electric resistance welding
- gas welding
- forge welding
Q20 | Hard peening is
- hammering the weld across the length while the joint is hot
- hammering the weld along the length while the joint is hot
- hammering the weld along the length while the joint is cold
- hammering the weld across the length while the joint is cold
Q21 | A rivet is specified as a 20mm rivet. What does it mean?
- none of the mentioned
- shank dia 20mm
- head dia 20mm
- both head and shank dia 20mm
Q22 | In hand riveting die is a part of hammer.
- true
- false
- topic 3.5 riveted joints for structures
Q23 | The amount by which the two rods to be joined are drawn together is called as?
- draw
- portray
- lead
- pitch
Q24 | Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)
- 31mm
- 35mm
- 36mm
- 40mm
Q25 | Among punching and drilling, which is cheaper?
- punching
- drilling
- equally expensive
- cannot be determined