Agricultural Engineering Set 43

Other topics

Practice Mode Previous Next
On This Page

This set of Agricultural Engineering Multiple Choice Questions & Answers (MCQs) focuses on Agricultural Engineering Set 43

Q1 | Transmission oil should be changed after
  • 750 hours
  • 800 hours
  • 1000 hours
  • 1200 hours
Answer: 750 hours
Q2 | Venturi unit is connected to the
  • Fuel injection pump
  • Engine inlet manifold
  • Engine exhaust manifold
  • None of these
Answer: Engine inlet manifold
Q3 | Ignition delay of high-speed engine should be about
  • 0.01 second
  • 0.001 second
  • 0.0001 second
  • None of these
Answer: 0.001 second
Q4 | A hydrograph is a plot of
  • Stream discharge against time
  • Rainfall intensity against time
  • Cumulative runoff against time
  • Cumulative rainfall vs time
Answer: Stream discharge against time
Q5 | The porosity index of relative volume of pores is influenced by
  • Texture
  • Structure
  • Both (a) and (b)
  • None of these
Answer: Both (a) and (b)
Q6 | Settlement of an embankment depends on
  • Void ratio
  • Density of soil
  • Water viscosity
  • All are correct
Answer: Void ratio
Q7 | The seeding behind plough is done by a device known as
  • Seed drill
  • Malobansa
  • Planter
  • Dibbler
Answer: Malobansa
Q8 | Throttle system controls the
  • Engine load
  • Amount of air fuel mixture
  • Both (a) & (b)
  • None of these
Answer: Amount of air fuel mixture
Q9 | Lead mid battery is generally used in
  • Tractors
  • Aircraft
  • Light Motors
  • None of these
Answer: Tractors
Q10 | In inclined draper, the major factor causing the separation of grain is
  • Shape and size
  • Shape and surface texture
  • Shape and weight
  • Weight and size
Answer: Shape and surface texture
Q11 | In leanest mixture, the fair fuel ratio is about
  • 12;1
  • 14;1
  • 15;1
  • 20;1
Answer: 20;1
Q12 | Watershed is a
  • Drainage basin contributing the runoff to a single outlet
  • Hydrological entity
  • Unit of area extent in which hydrologic cycle completes
  • All are correct
Answer: All are correct
Q13 | Insulated metal of solar cooker is
  • Black from outside
  • Black from inside
  • Black from out and inside
  • White from out and inside
Answer: Black from outside
Q14 | Pressure in hole type nozzle varies from
  • 15-20 MPs
  • 15-25 MPs
  • 17-34 MPs
  • None of these
Answer: 17-34 MPs
Q15 | A hammer mill type thresher has
  • Hammers
  • Beaters
  • Close cylinder casing
  • All are correct
Answer: All are correct
Q16 | A wire (standard wire gauge) used in secondary coli is about
  • 25 SWG
  • 30 SWG
  • 40 SWG
  • 50 SWG
Answer: 40 SWG
Q17 | Soil erosion is a
  • Fluvial work
  • Geomorphologic work
  • Both (a) and (b)
  • None of these
Answer: Both (a) and (b)
Q18 | Which of the following items utilizes direct energy of sun
  • Solar heater
  • Solar cooker
  • Solar cell
  • All are correct
Answer: All are correct
Q19 | High speed diesel is used in
  • High speed diesel engine
  • Low speed diesel engine
  • Petrol engine
  • Aircraft engine
Answer: High speed diesel engine
Q20 | The boiling range of petrol is
  • 30 to 180?C
  • 30 to 200?C
  • 30 to 230?C
  • 30 to 250?C
Answer: 30 to 200?C
Q21 | A part that connects piston with connection rod is
  • Piston ring
  • Gudgen pin
  • Safety pin
  • Camshaft
Answer: Gudgen pin
Q22 | The primary objective of level bench terrace is to
  • Conserve water and control erosion
  • Reduce runoff
  • Make steeply land cultivable
  • All are correct
Answer: Conserve water and control erosion
Q23 | Propeller type unit runs at a speed of
  • 100-200 rpm
  • 200-300 rpm
  • 300-400 rpm
  • 400-500 rpm
Answer: 300-400 rpm
Q24 | A plunger type hand duster is suitable for dusting
  • Small area
  • Medium area
  • Large area
  • All are correct
Answer: Small area
Q25 | The cam lobes of camshaft helps in
  • Opening and closing the valves
  • Driving the timing gear
  • Driving flywheel
  • Operated crankshaft
Answer: Opening and closing the valves
Previous Next