On This Page
This set of Agricultural Engineering Multiple Choice Questions & Answers (MCQs) focuses on Agricultural Engineering Set 10
Q1 | Sun radiation temperature corresponding to black body temperature is at about
- 3000 K more
- 5000 K more
- 6000 K more
- 7000 K more
Q2 | In disc harrow the angle made by the axis of the arbor bolt with the direction of travel is
- Disc angle
- Tilt angle
- Gang angle
- None of these
Q3 | The PTO HP of a tractor is
- Less than drawbar
- More than engine HP
- More than drawbar HP
- Less than friction HP
Q4 | Oil pump is driven by
- Oil pump is driven by:
- Timing gear
- Crankshaft
- All are correct
Q5 | The mould board plough absorb side forces mainly through the
- Share
- Mould board
- Land disc
- Frog
Q6 | A splined shaft used for taking off power from engine is
- Final drive
- Drawbar
- Power takes off
- Differential
Q7 | One bar is equal to
- 1 Kpa
- 5 Kpa
- 10 Kpa
- 100 Kpa
Q8 | Parboiling of paddy is done to
- Achieve maximum recovery of head rice
- Minimise the broken percentage
- Reduce the milling losses
- All are correct
Q9 | Centrifugal governor is also termed as
- Maximum speed governor
- Minimum speed governor
- Both (a) & (b)
- None of these
Q10 | Which of the biogas plant has digester tank and gasholder as combined unit?
- Floating dome type
- Fixed dome type
- Both (a) & (b)
- None of these
Q11 | The camshaft controls
- Valve closing
- Valve opening
- Valve timing
- All are correct
Q12 | The mechanical efficiency of spray pumps ranges from
- 50-60%
- 50-70%
- 50-80%
- 50-90 %
Q13 | Heavy smoking in an engine during operation may be due to
- Rich mixture
- Overloading
- Late injection
- All are correct
Q14 | Medium size bullock can develop
- 0.50 to 0.75 hp
- 0.75 to 1.0 hp
- 0.75 hp to 1.1 hp
- 1.0 to 1.5 hp
Q15 | Tractor front mounted reaper is operated at a forward speed of
- 1.5 km/h
- 2.0 km/h
- 2.5 km/h
- 3.0 km/h
Q16 | The uneven furrow formation in disc ploughing is due to
- Disc angle is not uniform
- Loose bearing of disc
- Hitching defects of disc plough
- All are correct
Q17 | The increase in tilt angle of disc plough influences
- Penetration of disc
- Width of cut
- Reduce penetration of disc
- Reduce width of cut
Q18 | The fan of radiator is driven by
- Camshaft
- Crankshaft
- Flywheel
- All are correct
Q19 | Contour trenching is performed to
- Control the landslide from the hill face
- Conserve the moisture
- Both (a) & (b)
- None of these
Q20 | A thresher causes more seed damage if
- Speed is increased
- Clearance increased
- Speed is decreased
- Feed rate is reduced
Q21 | Hand dropper consists of
- A serrated blade
- A pair of serrated blade
- A plane blade
- A pair of plane blade
Q22 | The shape of furrow cut by MB plough is
- V-shape
- L-shape
- W-shape
- M-shape
Q23 | Secondary fuel filter is used to remove the particles of size
- 1 Micron
- 2 Micron
- 3 Micron
- 4 Micron
Q24 | The gang angle of disc harrow is adjusted in the range of
- 0-30?
- 30-60?
- 60-90?
- Above 90?
Q25 | Erosivity is the
- Climatic aggressiveness
- Soil aggressiveness
- Both (a) and (b)
- None of these