On This Page
This set of Metrology and Measurements Multiple Choice Questions & Answers (MCQs) focuses on Metrology And Measurements Set 9
Q1 | Which of the following is correct for selective assembly?
- not suitable for industrial purposes
- cost increases due to automatic gauging
- wastage is high due to selective selection
- this method is followed in ball and roller bearing units
Q2 | Which of the following is used to check change in ocular lines position due to column rotation in universal micrometer?
- dial indicator
- slip gauges
- control shaft
- universal microscope
Q3 | What is the least count of clinometer which is used to check reading of column rotation used for setting of helix angles in universal micrometer?
- 1’
- 2’
- 3’
- 4’
Q4 | How 34’ can be built by using angle gauges?
- 27’+9’-3’+1’
- 26’+10’-2’
- 27’+10’-3’
- 27’+8’
Q5 | In how many series the gauges can be divided?
- 1
- 2
- 3
- 4
Q6 | What is the approximate size of angle gauges?
- 76mm long and 16 wide
- 85mm long and 26 wide
- 16mm long and 75 wide
- 70mm long and 18 wide
Q7 | What is the accuracy of master angle gauges?
- 0.1 sec
- 1 sec
- 0.25 sec
- 3 sec
Q8 | Which gauges are present in the first series (degree) of angle gauges?
- 5°, 10°, 15°, 25° and 40°
- 1°, 3°, 9°, 27° and 41°
- 1°, 5°, 9°, 25° and 45°
- 5°, 10°, 15°, 30° and 45°
Q9 | How many sets of angle gauges are available?
- 1
- 2
- 3
- 4
Q10 | What are the two grades of angle gauges?
- master and tool room
- precise and normal
- standard and industrial
- high and low
Q11 | How angle greater than 90° is measured?
- by repeating gauges
- using square plate
- using sine bar
- using auto collimator
Q12 | Which of the following is not a gauge from standard B angle gauges?
- 0.05’
- 1’ c) 27’
- d) 30
Q13 | Which of the following is not true about metrology lasers used in laser inspection?
- these are high-power instruments
- used for rapid non-contact gauging of delicate parts
- have low optical cross-talk
- wide dynamic range
Q14 | What is the wavelength of light produced by He-Ne laser in laser inspection?
- 6988 Å
- 5328 Å
- 5928 Å
- 6328 Å
Q15 | Which technique is not suitable to measure large diameter parts or large gaps?
- diffraction pattern technique
- scanning laser technique
- photodiode array imaging
- laser triangulation sensor
Q16 | Which of the following is true about resolution in two frequency laser interferometer?
- straightness resolution – 90 nm
- angular resolution – 3 arc seconds
- flatness resolution – 2 nm
- linear resolution – 1 nm
Q17 | How much accuracy can be achieved by photodiode array imaging?
- ±0.05 μm
- ±0.15 μm
- ±0.5 μm d) ±0.25 μm
Q18 | Which application is ideally suited for two frequency laser interferometer?
- pitch and yaw measurement
- hole diameters
- thickness measurement
- measurement of edge locations
Q19 | The location of the image spot directly depends on which factor in laser triangulation sensor technique?
- wavelength of laser
- measuring range
- standoff distance
- focal length of lense
Q20 | Which technique from given laser inspection techniques is useful for measuring the diameter of hot steel bars?
- laser scanning gauge
- frequency laser interferometer
- laser triangulation sensors
- photodiode array imaging
Q21 | Where does wire is placed in a measurement of diameter using the technique of gauging wide diameter from the diffraction pattern formed in a laser beam?
- between collimator and lens
- between collimator and source
- between collimator and plane of measurement
- between collimator and detectors
Q22 | How many sensors are needed to measure part thickness by using laser triangulation sensors?
- 1
- 2
- 3
- 4
Q23 | What precise movement does CMM have?
- precise movement in x coordinate
- precise movement in x and y coordinates
- precise movement in y and z coordinates
- precise movement in x, y and z coordinates
Q24 | Which type of CMM is most suited for large heavy workpieces?
- cantilever type
- bridge type
- horizontal boring mill type
- floating bridge type
Q25 | Which direction is sensed by a linear measurement transducer used in CMM?
- positive direction only
- negative direction only
- both positive and negative direction
- not used to sense directions