What is the maximum gross weight of the 60M
22,000 lbs
Aluminum paneling is used for added E3 protection. Where aluminum paneling couldn't be used, ______ was used
aluminum mesh
What is the minimum crew for the 60M?
Pilot and copilot
Which flight control computer is located in the nose compartment?
#2 FCC
The wide chord blade has what type of spar?
Graphite Epoxy
The landing gear is designed to absorb a landing rate of up to ____ feet per-second
39
For flights over 6 hours, the engine oil level should be ________
at the full mark
Pilot seats are ballistic tolerant up to ______ ordinance and are energy absorbing
7.62 mm
How much ground clearance does the landing and searchlights have when extended?
Less than one-foot
Blades have a _____ degree twist
16.3 degree
What is the main rotor diameter of the 60M helicopter?
53 foot 8 inches
How wide is the 60M at its widest point?
14 feet 4 inches
The _______ provides pneumatic power for main engine start, cabin heating and electrical power for ground operations and in-flight emergency electrical power
APU
The main transmission has a built-in ______ forward tilt
3 degree
The cargo hook is used to carry external loads up to _______ lbs
9,000 lbs
Accumulator pressure gage should read _____ PSI for APU starting
2800
What changes the direction, transmits torque and reduces shaft speed from the main gear box to the tail rotor gear box?
The intermediate gear box
The tail wheel swivels ______ degrees on a yoke assemly when unlocked
360 degrees
The bottom trailing edge of the tail pylon has an aerodynamically shaped fairing, with a _____ degree of camber to decrease the amount of tail rotor pitch/anti-torque required in foward flight
7 degree
The helicopter has a variable angle of incidence stabilator to enhance _____ qualities
handling
Where is the #1 flight control computer located?
aft avionics compartment
Why should you not store any items below the pilot seats?
Any obstruction will increase the probability and severity of injury
What is the purpose of the Reversionary Switch Panel?
Provides a means of manually selecting cross side data sources for the pilot and copilot MFDs
What is the purpose of the I-Event switch
To capture intermittent events such as noise and vibrations
How are the MFDs numbered?
The MFDs are numbered from left to right, one through four
Where is the Stabilator indicator located?
Upper left corner of the PFD
The digital clock has an internal battery that will keep it functioning for ...
one year
The radio control panel on the lower console is connected to which radio?
AN/ARC-231-3
How can the tailwheel be locked in the trail position?
The tailwheel can be locked in the trail position by presing the Tailwheel LOCK/UNLK switch to indicate LOCK
What are the three positions of the Backup Hydraulic Pump switch?
ON, OFF, AUTO
What is the purpose of the Auxiliary Fuel Management Panel?
It contains all controls for operating the Crashworthy External Fuel System (CEFS)
Where are the controls to operate the Common Missile Warning System from the cockpit?
The dispenser control panels located on the lower console contains all necessary controls to operate the Common Missile Warning System from the cockpit
What are the 4 Power Control Lever (PCL) positions?
OFF-IDLE-FLY-LOCKOUT
How is cockpit ventilation controlled?
Ventilation is controlled through a switch on the upper console marked VENT BLOWER
How many fire extinguisher handles are in the aircraft?
There are two engine fire extinguisher handles are on the power control quadrant and one APU T-handle on the upper console.
The ICS system consists of how many panels located throughout the aircraft?
Five
How is a radio's audio disabled?
Pull up ono the associated radio's volume control knob
What does the ICS consist of?
The ICS is a centralized system consisting of one Interface Control Unit (ICU); five ICS control panels, and cyclic and collective switches
How many modes are there available in the ICS system?
Four
the CVR / FDR is used primarily for what?
Accident investigation
the acoustic beacon will transmit a signal for how long?
A minimum of 30 days
What controls the START / STOP function of the CVR / FDR
DCUs
When the main transmission oil pressure is normal (>20 psi) the CVR/FDR will _______
start recording
What kind of protection is offered to the pilot and copilot against small arms fire?
Back, Side, and Bottom ballistic protection
VLEAs may be manually adjusted for occupants ranging in weight from ____ to _____
The VLEAs may be manually adjusted for occupants ranging in weight from 130 to 250 lbs optimizing the occupant's protection.
Red bands showing on the VLEA housing indicates what?
The seat has stroked
What directions can the Martin Baker Seat be adjusted to face?
These seats can be adjust to face left, right, forward, or aft
what is the purpose of the inertia reels on the seat back and bottom?
It gives the wearer freedom to move about his station
How many passengers will the 60M normally carry in a "seats in" configuration, not including crew members?
Eleven
What are the two types of restraints offered to the passengers in a 60M?
Belt and shoulder harnesses
What does the flight/mission display system (F/MDS) consist of?
4 multifunctional displays
Reversionary switch panels
Electronic Flight Information System (EFIS)
Multifunction and Collective Slew Controllers
The Outboard No.1 and No.4 MFDs default to the ______ upon power-up. the inboard No.2 and No.3 MFDs default to the _______ display
PFD
EICAS
The pilot and copilot Reversionary Switch Panels allow the pilots to?
select the Alernate Data Source
What do the MFSCs provide?
They provide control of hte MFD cursor, cursor activation, menu navigation and selection
Selection of the MFD display and various submodes are accomplished using each MFD's ______________________
24 bezel keys - 6 keys per side
The PFD _____________ annunciations are displayed as a yellow parameter label with a double-headed yellow arrow above
miscompare
Where is the Stabilator Position Indicator located?
The upper left corner of the PFD
The Stabilator Position indicator will be displayed in what colors for which modes of operation?
White for the Auto Mode and Limited Auto Mode;
Yellow for the Manual Mode
An input failure of the airspeed data will result in what being displayed?
A Red IAS Fail Flag
The pitch and roll attitude inputs to the PFD are provided by what?
The EGIs
Where is the standard lateral deviation scale and pointer located?
In the lower center area of the ADI
A failure of an EGI would result in what two major items being removed from the Primary Flight Display
The ADI and HSI
What does a yellow readout with an R represent in the wind speed and direction field?
Remembered winds
The course pointer can be adjusted by the OBS knob for all navigation sources except?
FMS
The Co-pilot has ILS as their NAV source and the Pilot has FMS. The #2 FMS fails and the Pilot selects the FMS Reversion switch. How would the annunciation appear?
FMS1 (yellow text)
What additional items can be displayed on the ARC submode that is not displayed on the FULL submode
The range rings
Stormscope
Flightplan
Hover point
How are Strikes and Cells displayed when the Stormscope is enabled?
Strikes are displayed as an X
Cells displayed as a +
What does the Velocity Vector and Acceleration cue represent?
Velocity vector represents the direction and velocity the aircraft is currently moving. The Acceleration cue represents the directional acceleration.
The PFD wind symbology is white when the current wind information is displayed but will be ___________ whenever the IAS is less than 40 kts
Yellow
When the Power Pod TGT is in the 2.5 minute range, it is displayed as _______________
Yellow Box and Two Yellow Balls
On the PFD display, a black on red annunciation indicates the ________ to the MFD for that parameter has failed or is not being __________
input, received
The Vertical Deviation (GS) pointer is displayed as a _____________
Diamond
The ___________ readout is displayed below the barometric altimeter and is displayed in _____________
correction setting (altimeter setting), inches of Hg
The Vne indication will extend in a counterclockwise (decreasing airspeed) direction along the scale to show a reduced Vne IAS value when the ____________ is in the __________
stabilator, manual mode
The ND FULL display is oriented ________
Heading up
The ND PLAN mode is oriented ________
True North up
Map annunciations are displayed (located) ______________ and will be ____________ when multiple annunciations are active
Bottom center
Prioritized
EICAS display information consists of three groups of parameters/data _______________________
Engine/Rotor/Transmission data
Fuel data
Caution/Advisory data
What does a large red X represent when displayed on the EICAS display?
An Engine Out conditino
Within each of the EICAS windows, cautions and advisories are displayed in chronological order, with the most recently activated sipalyed at the _____ of the window
top
A miscompare of EICAS data will be displayed with the ______________
label in inverse video NG
What determines which FMS becomes the Bus Controller (BC)
The first panel to complete its PBIT
What are the first four lines of data on the FMS display called?
Header
The pilot's FMS header defaults to what on power up?
NAV
How many waypoints may be put into a flight plan?
99
How many "store points" may be captured?
25
IG2" indicates which navigation solution?
Blended solution from the #2 EGI
What does the "STS" annunciation display at the top of the FMS mean?
A change in status has occurred
A Box around a parameter on any given screen indcates what?
that the parameter may be edited
Manual selection of the aircraft navigation solution can be accomplished by accessing which FMS page?
EGI
How can you quickly "capture" a Target Store point?
Press the FIX fixed function key twice
How is FLPN-A or FLPN-B initiated?
From the Flight Plan EDIT page, select ENGAGE
Which page allows the pilot to change the com data/frequency assigned to a specific preset?
DAT (Mission Data Page)
What is the purpose of the flight plan Sequence Next function when in the Auto mode?
Allows the operator to sequence to the course between the next pair of waypoints
60M basic weight
13,000 lbs
Max sling-load weight
23,500 lbs
Interior panels are metalized _____________
nickel Nomex fabric
#2 flight control computer controls your _______
trim
APU accumulator pressure gage should be __________
2800 psi
the helicopter has a variable angle of incidence stabilator to enhance __________ qualities
handling
What are the two locations where you can use Stormscope
Arc submode
Nav display
PFD HOVER sub-mode display has three sub-modes that are
Full
Arc
Hover
Input error with the system that has digitis is __________
three red dashed lines
EICAS page miscompare looks like
black text on yellow box
Yellow sabilator caution says...
STAY MAN MODE
If going into manual mode, the VNE arc moves ____________
clockwise to increase
What happens to airspeed indicator when you fly into VNE arc?
It turns red and digital read out turns red
Barometric altimeter setting is located ______ the altimeter
below
Differene between standard lateral deviation scale and expanded deviation scale
Expanded LOC
Expanded LOC has four circles plus the + symbol
LOC (2 square and a diamond)
Accompanied by glide slope deivation scale, depicated as position diamong
What does the MFD inform the pilot
Theres been a change in the status of the FMS
Stormscope is displayed on the __________ (full page) and the ___________ (sub-mode)
NAV display
PFD arc
When symbology is white, when does it turn yellow?
Below 40 kias
1 square = ____ min
1 square 1 ball = ___ min
1 square 2 ball = _____ min
30 min
10 min
2.5 min
What does the reversionary switch allow
Allows you to select an alternate data source
Threats can be displayed on TAC map and NAV display, normally on ________
nav display
Engine and transmission data is only depicted on the _________
EICAS
Com radios can create up to _________ for each radio band
20 presets
Blended solution is _________
INS1 or 2 are purely _____________
EGI NAV is ___________________
inertial navigation with GPS aiding
purely inertial navigation
inertial navigation without GPS aiding
Number of waypoints possible =
Number of storepoints possible =
99 waypoints
25 storepoints
Boxed parameters on the display conventions allow users to ________
edit the selected field
During system start up, FMS-1 initially boots to the ____________, FMS-2 to the __________
COM header
NAV header
The first FMS to complete the __________ becomes the Bus Controller, the second becomes the ______
PBIT
Backup bus controller (BBC)
What are the first four lines of the FMS called?
Header, it defaults to the left
What is line 5 on the FMS called?
Alert status line
How does hte pilot identify which FMS is the BUS controller?
BC in small text on alert status line
What are the functions of the radio select switch on the collective?
Cycles through radios
Calls up the comm page
Cycles through presets
FMS provides __________ and _________
data edit and entry capability
Steering cues are processed/commanded by what component/s?
The FCCs
What are the components of the Flight Director Sets
An independent Flight Control Computer (FCC)
A Flight Director/Display Control Panels (FD/DCP)
Two Multifunctional Displays (MFDs)
Sensors
Go ARND Switch and Remote Standby swtich on the cyclic grip
The FD processes signals from navigation and flight instrument sets to produce steering commands that are performed through which axes?
Collective (vertical), pitch, and roll
What are the functions of the #2 FCC?
Provides steering cue commands for display on the MFDs
What are the five roll NAV sources?
FMS
VOR
TCN
LOC
BC
Once the GO ARND parameters of a wings level climb at 750 fpm and 70 KIAS has been achieved, what happens?
GO ARND disengages, then VS hold and IAS hold engage
What are the three HVR modes?
HVR DECL, HVR VHLD, & HVR POSN
Which Roll NAV source can not be ARM?
FMS
To engage the ILS DECL mode, the indicated airspeed must be above ____ knots
70 kts
To engage the HVR VHLD mode, the airspeed must be below _______ knots
60 kts
The Go Around mode provides collective, pitch, and roll cues and FPS commands to establish a wings level _______ fpm Rate of Climb while maintaining ______ knots
750 fpm
70 kts
To engage the aircraft level attitude recovery mode when in an unusual attitude, the aircraft must be above ______ knots
60 knots
ALTP captures ______ feet prior to the selected reference when ARM
300 ft
When engaging Hover Hold using the Trim Beeper below 60 kts, what two modes will capture on the FD/DCP?
Hover Mode and RAIT
ALTP drops offline ______ feet prior to the selected reference
50 feet
What are combinations of extreme attitude and pitch/roll rates from which the flight director will not be able to recover to a level attitude/hover?
Hover Mode
Go Around Mode
In order for you to see steering cues on the PFD, you must engage one or more ________ on the _______
modes on the flight director
Which reference modes are the only that can be armed? What happens to the others
Armed:
LOC
BC
VOR
TCN
The others are captured
What are the ways to engage standby mode?
Can be engaged at any time by deselecting all engaged modes onf the FD/DCP,
or by pressing the RMT SBY switch on the corresponding cyclic grip
Pressing the cyclic or collective trim release will cause the FD to enter an ________________ displayed by the effected mode switch turning __________ while trim release is depressed
active (temporary) standby
Amber
Altitude Pre-Select (ALTP) Mode can be arrmed at _________
any time
In order for you to see steering cues on the flight display, you must....
engage one or more modes on the flight director
If during the deceleration process, the pilot desires to maintain a specific hover velocity, _____________ can be engaged by pressing the cyclic ________ switch
Upon releasing the ____________ switch, the present aircraft is lateral and longitudinal _____
HVR VHLD
TRIM REL switch
TRIM REL switch
Velocity references (VREF)
How to go from Hover velocity to Hover POSN
Plunge cyclic beeper to start a decel, once less than 1 knot, it will change to HVR POSN
Cyclic trim beeper plunger over 60 kias always engages ________________
barometric altitude hold
Anytime the lights are flashing on the PCMCIA card slots, it is an indicator that __________________________
the DTA is writing or updating information to the cards
PCMCIA cards can only be inserted into the DTU with the ____________
INSERT label facing aft
User partition is for _____________ only
file management
How does the pilot view processed data?
Engage one or more modes on the flight directory
What component processes steering cues
FCC
What system gives you your attitude and heading?
EGI
What nav mode is the only one that gives time-to-go?
FMS
When does radar alt hold mode become functional?
Below 1500'
Not associated with an airspeed
In order to use FMS NAV mode, what must you do?
FMS NAV selected on flight director
Select flight plan
How do you engage HVR DECL?
Cyclic trim beeper
How do I engage HVR VHLD
Press cyclic trim release while in HVR DECL
How do I command attitude recover mode?
Press in cyclic trim beeper over 60 kias